When a new house sewer is installed in NYC there are six basic types of sewer connections. The most usual is the spur connection and it is also the least costly when it is available. As time has passed it is more and more usual for building lots to be split and previously undeveloped lots now being developed. Due to that fact more often than in the past other types of connections have to be utilized and built. If you are developing a property in NYC it is important to familiarize yourself with these connections as they can add substantial cost to a project.
A spur connection is the most common of all connections used for a house sewer. Basically a spur on a city sewer is a Y in the city sewer with a plug on the outlet side to be used for future connections. The spur itself is typically 6″ with the exception being 8″ sizes in Manhattan where the minimum size for a house sewer is 8″. Having a spur available for connection prevents the need for drilling into the public sewer which is more costly and if not done properly can cause damage to the public sewer. In most cases spurs are ideal for a new sewer connections.
Fold in sewer connections
When the city sewer is only one size larger than the connection size required and no spur exists a sewer contractor must fold in a new spur in most cases. This typically occurs when the public sewer is 8″, a size no longer legal as a public sewer in NYC, and a 6″ connection is required. A fold in requires actually removing sections of the city sewer, then folding in three new sections of pipe one of which is a Y to be used as the connection for the house sewer. All new sections of pipe must then be encased with an approved concrete mixture. A new fold in connection adds to the cost of a new sewer installation.
A curb connection is usually found on two occasions and when found avoids the need to open the roadway in order to complete a sewer installation. The first case is when a new public sewer is installed and as part of the project a new pipe is installed up to the curb line for each building and all buildable lots that have not yet been developed. The second case where curb connections are found is when a previous building has been demolished and the service for that property was plugged at the curb line, as is required by code. When a property is redeveloped a plugged curb connection can be frequently re-used at a substantial savings to the property owner. Get free expert advice
Drill in sewer connections
When a new connection is required into a NYC sewer and no connection is available the most usual connection required is a drill in. This is performed using a core drill machine. It is not permitted to chop into a NYC sewer using hand or power tools. A hole is carefully cored through the NYC sewer a specific size larger than the pipe size to be connected. In most cases the city sewer must be prepared before the core drill is done by encasing the public sewer in concrete. In other cases a concrete cradle must be installed under the public sewer. The concrete reinforces and strengthens the city sewer from the added stress of the core drilling and the future house connection. A drill in connection does not add substantially to the cost of a new house sewer. Drill in sewer connections are made routinely for new house connections throughout new York City.
A riser connection is a vertical connection built on the top of a city sewer for use as a connection for a house sewer. Depending on the size and type of the public sewer different designs are used in the construction of a riser. It is usual for such a connection to be required when the depth of the public sewer is greater then 13′ or if a groundwater or rock condition exists. In these cases it is meant to alleviate the cost to property owners of having to excavate to great depths or through groundwater and rock in order to connect properly to the main sewer line.
A riser is also required when the difference in elevation from the point where the house drain exits the building to the city sewer is greater than the pitch that is allowed to be used. As sewers work on the principal of gravity, pitching the pipe is used so the waste-water runs off properly. Only a maximum of 1′ of pitch is permitted for every 4′ of run of pipe. Therefore a riser must be built sometimes when the difference in elevation is too great to use allowable pitch. Risers must always be one size greater than the size of the connection size from the building. In NYC where the minimum size of a sewer connection is 6″ the size of a typical riser is 8″.
When a riser must be built they are carefully inspected by DEP field personnel and must conform to accepted design standards. All risers must be encased with an approved ready-mix concrete and reinforced with re-bar to provide a long-lasting connection. After the installation is signed off by the DEP the future maintenance and ownership of it reverts back to the NYC DEP. All such installations are built with a clean-out on the top as a way to clean out any possible future stoppages. If a riser has to be built it will add at least a few thousand dollars to the cost of an installation. Other than having to build a new manhole it is the most expensive connection to build.
New manhole connection
In rare instances a new NYC DEP approved manhole has to be built for connection to the city sewer. This is required typically for very large house sewer connections such as for a 12″ house sewer. This type of connection involves purchasing precast concrete rings from an approved vendor and a top slab with a ring and manhole cover. All the steps involved in building a manhole are very closely monitored and inspected by NYC DEP field inspectors.
In terms of cost the manhole material alone costs in excess of $2,000.00 including delivery. Once other costs such a labor, ready mix concrete, and roadway restoration are factored in a manhole connection is by far the costliest means to connect to a city sewer. In some cases it is less expensive to install two smaller sized house sewers in order to avoid having to build a new manhole connection.
How can this information help you?
New house sewer connections can be a substantial part of the cost of a project. Being familiar with the different types of connections and the cost involved can be an important step in keeping costs down. With over 60 years of combined experience Paul R. Balkan and David Balkan possess a wealth of knowledge about NYC water main and sewer work. If you have a question or need additional information they welcome your inquiry. All inquiries are responded to promptly – See if Balkan Sewer And water Main Service can help you today, contact us via our Sewer and Water information request form. Get a free no-obligation site visit
Read related articles about house sewer connections
- New Sewer Line Cost Is Affected By The Depth And Connection Type Posted on: January 22, 2014
When a property is developed, or a building is upgraded, […]
- Sewer Replacement In Astoria Queens, Home Owner Hires The Expert Posted on: June 20, 2013
Recently a sewer replacement was needed in Astoria Queens on […]
- New Home Sewer Lines In The Bronx Installed Through Solid Rock Posted on: May 9, 2013
New home sewer lines are a vital part of any […]
- NYC Sewer Contractors Need Accurate Records Before Excavating Posted on: March 28, 2013
Sewer contractors in NYC depend upon a number of factors […]
- Broken Bronx Sewer Line Due To Shoddy Plumbing Work Posted on: January 2, 2013
A relatively new house in the Bronx was suffering from […]
Joseph L. Balkan, Inc. | Sewer and Water Main Specialists
130-01 Jamaica Avenue Richmond Hill, NY 11418
Phone: (718) 849-0900 | Espanol (718) 943-5720 | Fax: (718) 849-9570